|
9 members (TBM, Sir Percival, nippymog, +8Rich, brownbaker, chanteclair, SwissMogFan, BobtheTrain, teifistar),
141
guests, and
27
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
|
Currency
by Dean-Royal - 09/06/23 10:10 AM
|
|
|
|
|
|
|
|
|
|
|
|
|
Forums32
Topics45,177
Posts765,172
Members8,359
| |
Most Online1,033
Dec 28th, 2019
|
|
|
There are no members with birthdays on this day. |
|
|
|
Joined: Dec 2011
Posts: 422
Learner Plates Off!
|
OP
Learner Plates Off!
Joined: Dec 2011
Posts: 422 |
I am about to fit a rear carrier on my +4, i have no bumpers or overiders just the rear valance without the holes for the overiders. I have bought some brackets that fit into the tubes on the chassis but its quite difficult to mark where to cut the holes for the brackets can anyone give me some measurments and photos from their car to give an idea of where to cut.
Any advice most welcome.
2020 Plus Four
1981 Lambretta GP225
1960 Lambretta LI 125
|
|
|
|
|
Joined: Feb 2016
Posts: 6,135
Talk Morgan Sage
|
|
Talk Morgan Sage
Joined: Feb 2016
Posts: 6,135 |
Don't know if this helps. ![[Linked Image]](https://i.imgur.com/p9vaEo7.jpg) It shows a freshly painted overrider support inserted back into chassis tube with fresh main bolt and extra dome head Allen locating screw into matching pre-tapped hole in support. You can just see the forward end of support through the other redundant hole in tube to define how far it should go in.
Richard
2018 Roadster - Red/Magnolia - Morton
1966 Land Rover S2a 88 - Lenny
1945 Moto Guzzi Airone
|
|
|
|
|
Joined: Jul 2007
Posts: 23,966 Likes: 3
Brooklands Register contact Member of the Inner Circle
|
|
Brooklands Register contact Member of the Inner Circle
Joined: Jul 2007
Posts: 23,966 Likes: 3 |
I have no over riders just the rack. I'm on my hols in Tobago right now. PM me next week if you still need details.
JohnV6
2014 Brooklands Edition Roadster "Brookland's Belle" #5 of 50
|
|
|
|
|
Joined: Jun 2015
Posts: 1,422
Has a lot to Say!
|
|
Has a lot to Say!
Joined: Jun 2015
Posts: 1,422 |
Not easy to measure because of curves but I have taken two measurements on my 2011 +4.
Centre of tube measured horizontally to outside edge of the under-valance is 80mm
Centre of tube, measured down from the flat horizontal section of the under-valance that bolts up under the sloping rear of car is 93mm.
I would drill perhaps a 8mm hole in that area first and see how close it is, as it should put you in the right area.
Doug
2011 +4 in Rich Maroon
1972 750 “ComDom” sprinter
1958 Triton 650
1992 Triumph Trophy 900
|
|
|
|
|
Joined: Dec 2011
Posts: 422
Learner Plates Off!
|
|
OP
Learner Plates Off!
Joined: Dec 2011
Posts: 422 |
Thanks everyone , that gives me something to work with.
2020 Plus Four
1981 Lambretta GP225
1960 Lambretta LI 125
|
|
|
|
|
Joined: Feb 2016
Posts: 6,135
Talk Morgan Sage
|
|
Talk Morgan Sage
Joined: Feb 2016
Posts: 6,135 |
Posted earlier but in wrong thread  see here
Richard
2018 Roadster - Red/Magnolia - Morton
1966 Land Rover S2a 88 - Lenny
1945 Moto Guzzi Airone
|
|
|
|
|
Joined: Dec 2011
Posts: 422
Learner Plates Off!
|
|
OP
Learner Plates Off!
Joined: Dec 2011
Posts: 422 |
Fitted today , all went well, thanks to all who contributed.
2020 Plus Four
1981 Lambretta GP225
1960 Lambretta LI 125
|
|
|
|
|
Joined: Jul 2007
Posts: 23,966 Likes: 3
Brooklands Register contact Member of the Inner Circle
|
|
Brooklands Register contact Member of the Inner Circle
Joined: Jul 2007
Posts: 23,966 Likes: 3 |
JohnV6
2014 Brooklands Edition Roadster "Brookland's Belle" #5 of 50
|
|
|
|
|
