|
2 members (JMcL, MartO),
332
guests, and
31
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
|
|
|
|
|
|
|
Sold
by simon8201 - 09/09/26 01:46 PM
|
|
|
|
|
|
|
|
|
|
Wales
by Joske Vermeule, September 1
|
|
|
|
|
|
|
Forums39
Topics49,896
Posts838,016
Members9,635
| |
Most Online1,063
Jun 14th, 2026
|
|
|
|
Joined: Aug 2013
Posts: 1,562
Talk Morgan Enthusiast
|
Talk Morgan Enthusiast
Joined: Aug 2013
Posts: 1,562 |
I believe its approx £650 unfitted , sorry dont know the part number
|
|
|
|
|
Joined: Mar 2015
Posts: 902
Talk Morgan Regular
|
|
Talk Morgan Regular
Joined: Mar 2015
Posts: 902 |
|
|
|
|
|
Joined: Jan 2015
Posts: 245 Likes: 5
L - Learner Plates On
|
|
L - Learner Plates On
Joined: Jan 2015
Posts: 245 Likes: 5 |
I should have some backlash in it, both the ones Ive had have been about the same
|
|
|
|
|
Joined: Mar 2013
Posts: 722 Likes: 24
Talk Morgan Regular
|
|
Talk Morgan Regular
Joined: Mar 2013
Posts: 722 Likes: 24 |
Did a + 7 hours trip today and this F***ing bevel box noise makes us crazy.
It spoils a great part of the pleasure.
Please, please MMC come with a solution !!
Last edited by Laurens; 28/06/16 09:07 PM.
|
|
|
|
|
Joined: Mar 2015
Posts: 29
Just Getting Started
|
|
OP
Just Getting Started
Joined: Mar 2015
Posts: 29 |
If you look for my original post it will show what I did for a rebuild. I used Timken bearings and races for my rebuild. I recommend Lucas oil stabilizer for the box. You can run it at 100% but I thin it a little with 140W Lucas synthetic gear oil, 10%. After you install new bearings change out the oil in 1500 miles and check pinion preload without the seal installed. You want no less than 180 inch pounds with new bearings. If you backlash is no good you have to fabricate your own pinion shims.
"Know the black and white before you walk in the gray"
|
|
|
|
|
Joined: Mar 2015
Posts: 29
Just Getting Started
|
|
OP
Just Getting Started
Joined: Mar 2015
Posts: 29 |
Remove interior and trunk panel.
"Know the black and white before you walk in the gray"
|
|
|
|
|
Joined: May 2016
Posts: 72
Just Getting Started
|
|
Just Getting Started
Joined: May 2016
Posts: 72 |
I have just called Morgan, and pressed 2 for service and warranty, it rang through to leave a message, so I did. Do I need a part number for a recon, if I manage to get hold of them?
|
|
|
|
|
Joined: Aug 2013
Posts: 1,562
Talk Morgan Enthusiast
|
|
Talk Morgan Enthusiast
Joined: Aug 2013
Posts: 1,562 |
Believe me , they know what a recon bevel box is, regardless of part number !!! You shouldnt have to know their part numbers to order.
I suggest you keep ringing until you speak to a human.
|
|
|
|
|
Joined: May 2011
Posts: 1,625 Likes: 25
Talk Morgan Enthusiast
|
|
Talk Morgan Enthusiast
Joined: May 2011
Posts: 1,625 Likes: 25 |
I have found it easier to get through to the parts department.
2021 M3W
2013 M3W - Sold
1971 4/4 2 Seater
1934 Sports
|
|
|
|
|
Joined: May 2016
Posts: 72
Just Getting Started
|
|
Just Getting Started
Joined: May 2016
Posts: 72 |
I have found it easier to get through to the parts department. I have just sent an email to Mark Evans, as someone suggested. Fingers crossed.
|
|
|
|
|
