|
|
|
10 members (JohnHarris, AlyMatt, Image, 2949olivier, Hamwich, Cerberas, James B W, Sir Percival, Ricosan, Bunny),
249
guests, and
77
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
Wales
by Joske Vermeule, September 1
|
|
|
|
|
|
|
|
|
|
|
Forums39
Topics49,871
Posts837,682
Members9,596
| |
Most Online1,063
Jun 14th, 2026
|
|
|
|
Joined: Jan 2016
Posts: 121
L - Learner Plates On
|
OP
L - Learner Plates On
Joined: Jan 2016
Posts: 121 |
Can anyone suggest a good heat shield for a 1965 plus four 2 seater, I want to line the floor boards and firewall inside car then put a nice thin carpet over it thanks in advance
|
|
|
|
|
Joined: Sep 2011
Posts: 2,814
Talk Morgan Expert
|
|
Talk Morgan Expert
Joined: Sep 2011
Posts: 2,814 |
http://www.carbuildersolutions.com/uk/em...1040f0-86613517This is from a UK supplier, but you must have it stateside. It would have to go on the underside of floorboards if not to be deformed under carpet.
Gerry
|
|
|
|
|
Joined: Feb 2011
Posts: 1,500 Likes: 2
Talk Morgan Enthusiast
|
|
Talk Morgan Enthusiast
Joined: Feb 2011
Posts: 1,500 Likes: 2 |
dynamat works well. they have several versions. Some for sound and some for heat.
Cheers,
Mark
1934 SS MX4
1938 Series 1 DHC
1951 Plus 4
2005 Roadster
|
|
|
|
|
Joined: Jan 2016
Posts: 121
L - Learner Plates On
|
|
OP
L - Learner Plates On
Joined: Jan 2016
Posts: 121 |
|
|
|
|
|
Joined: Jan 2016
Posts: 121
L - Learner Plates On
|
|
OP
L - Learner Plates On
Joined: Jan 2016
Posts: 121 |
|
|
|
|
|
Joined: Dec 2011
Posts: 1,943
Talk Morgan Enthusiast
|
|
Talk Morgan Enthusiast
Joined: Dec 2011
Posts: 1,943 |
Dynamat on the inside does OK. But I needed to take a bit more care of Mrs. Button. 1963 +4-4 Str. I put 1" Bat insulation on the outside of the bulkhead between to engine and the bulkhead. As I worked in a Ship Yard I was familiar with Owens-Corning insulation. This 1" bat has a hard backing of fiberglas. I out a sheet of it and cut to fit. There are fasteners that glue to the bulkhead, go thru the insulation/backing and have a snap cap that fits on the stem. (best description I can come up with). It takes a bit to fit. But patience. I used "Great Stuff" to seal the holes around the wires etc. On the side of the bulkhead I made a 3" hole and a matching 3" hole on the bonnet. Covered the hole in the bonnet with a marine fixture (Plastic). Used a bildge blower to pump fresh air into the footwell next to Mrs. Button's feet. This goes on and on.
Mind You if it is hot outside it will be hot inside. I try to make my long trips in the Spring and Fall. Avoid the Summer.
Contact Me offline if You need more information. BTW: It does not look pretty.
Button
wmbutton@gmail.com
Seattle
Button
|
|
|
|
|
|
|
