|
7 members (Alan Patterson, Robbie, Mats, Lance, bmgermany, Image, Chris Cosher),
240
guests, and
42
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
|
|
|
|
|
|
|
Wales
by Joske Vermeule, September 1
|
|
|
Forums39
Topics49,909
Posts838,126
Members9,635
| |
Most Online1,063
Jun 14th, 2026
|
|
|
|
Joined: Apr 2016
Posts: 161
L - Learner Plates On
|
OP
L - Learner Plates On
Joined: Apr 2016
Posts: 161 |
Hi all,
Any advice on pulling outer bearing races from the hubs? The outer inner bearing came out easy. The oil seal too, then the inner bearing lifts right out. But both outer races are stuck in the hubs. Should I try and whack them out (gently of course), with a drift, or is one of those blind hole pullers is the way to go?
-Nelson
‘66 plus 4 2-seater
- Nelson
1966 Plus 4 RHD
|
|
|
|
|
Joined: Jan 2013
Posts: 1,149 Likes: 19
Has a lot to Say!
|
|
Has a lot to Say!
Joined: Jan 2013
Posts: 1,149 Likes: 19 |
I use one of these to push out evenly dont use a drift or if you damage the hubs..... You may need an attachment to the end of the rod to fit the bearing ![[Linked Image]](https://live.staticflickr.com/65535/50643263703_8e73bb9cea_o.jpg) Untitledpress by Robert & Ali Davies, on Flickr
Morgans 1934 MX, 1947 Series 1, 1956 +4 TR4, 2000 +4 T16
Triumph Herald 1969 13/60
Morris 1970
|
|
|
|
|
Joined: Feb 2007
Posts: 521 Likes: 2
Talk Morgan Regular
|
|
Talk Morgan Regular
Joined: Feb 2007
Posts: 521 Likes: 2 |
I’d use a brass dolly that way no damage.
Regards
Simon
Simon
2002 4/4
1936 Austin 12 light 4 Ascot saloon
2023 AMG Mercedes C300e estate
2021 Audi A1 sport
|
|
|
|
|
Joined: Aug 2015
Posts: 1,616 Likes: 143
Talk Morgan Enthusiast
|
|
Talk Morgan Enthusiast
Joined: Aug 2015
Posts: 1,616 Likes: 143 |
How bad are the bearings, bad enough to need replacing?
I run a thick bead of MIG weld carefully around the bearing track then when everything is still nice and hot, I belt them out with a large hammer and drift
Arwyn
|
|
|
|
|
Joined: Aug 2013
Posts: 3,383 Likes: 14
Talk Morgan Addict
|
|
Talk Morgan Addict
Joined: Aug 2013
Posts: 3,383 Likes: 14 |
Nelson
If you do choose to buy a bench press you won’t believe how useful they are. Not crazy expensive, a basic one is a few hundred dollars and it’s not just bearings that they can be used for.
King pin bushes pressed in and out, all sorts of assembly work, holding small parts for drilling (how many times have you needed 3 hands?) I even used mine to bend sheet steel and metal strip. I had hear of MogBoxes coming detached so fabricated a safety clamp using the bench press.
One of those things that have you wondering how you ever managed without one.
BR
Colin (Guys need ‘stuff’)
BR Colin
Who used to be a Spanner Juggler
|
|
|
|
|
Joined: May 2010
Posts: 9,554 Likes: 134
Needs to Get Out More!
|
|
Needs to Get Out More!
Joined: May 2010
Posts: 9,554 Likes: 134 |
If I had room I would get a press. Changing front discs last year....stuck onto the hubs. A press would have made that job easier! It would double up as a fruit press too. Mmmmmmm home brewed cider.
Plus Four MY23 Furka Rouge
|
|
|
|
|
Joined: Apr 2015
Posts: 450 Likes: 1
Learner Plates Off!
|
|
Learner Plates Off!
Joined: Apr 2015
Posts: 450 Likes: 1 |
This is for races which are impossible to remove any other way and it needs to be done with care and safety glasses! Run a weld round the inside of the race about middle of the width. When the weld cools the race will fall out. Bear this in mind when thinking of the stresses set up by welding chassis tubes like the M3W ones!
2013 M3W 1960 Velocette Venom and the Landrovardo!
|
|
|
|
|
Joined: Apr 2016
Posts: 161
L - Learner Plates On
|
|
OP
L - Learner Plates On
Joined: Apr 2016
Posts: 161 |
Great advice all. For those that use the press, it’s not a straight shot down at the bearing. How can you push them out with a straight press?
I did manage to get them out safely with a drift. But you really must angle the thing to get good purchase on the bearing race lip.
- Nelson
1966 Plus 4 RHD
|
|
|
|
|
