|
Forums34
Topics48,338
Posts812,951
Members9,203
| |
Most Online1,046
Aug 24th, 2023
|
|
|
|
Joined: May 2014
Posts: 5,107 Likes: 56
Black Rat Charter Member
|
Black Rat Charter Member
Joined: May 2014
Posts: 5,107 Likes: 56 |
Went to Cain yesterday for a service, right rear brake cylinder seized this is the 3rd one in ten years. Funny, it’s usually the left hand side that catches all the roadside puddles. It was the last 2 times, this time the right side was rusted solid. Surprisingly it passed the MOT not long ago.
Keith
2013 narrow bodied + 4 Ruby.
|
|
|
|
|
Joined: Jul 2022
Posts: 412 Likes: 47
Learner Plates Off!
|
OP
Learner Plates Off!
Joined: Jul 2022
Posts: 412 Likes: 47 |
Started it! Fired right up after a long winter's nap. Need a new ignition switch, however as this one is intermittent. It doesn't switch on every time I turn the key...
|
|
|
|
|
Joined: May 2014
Posts: 5,107 Likes: 56
Black Rat Charter Member
|
|
Black Rat Charter Member
Joined: May 2014
Posts: 5,107 Likes: 56 |
Found the rubber seal on the windscreen pillar was coming unstuck glue applied job done.
Keith
2013 narrow bodied + 4 Ruby.
|
|
|
|
|
Joined: Jun 2021
Posts: 1,779 Likes: 52
Talk Morgan Enthusiast
|
|
Talk Morgan Enthusiast
Joined: Jun 2021
Posts: 1,779 Likes: 52 |
Replaced my bonnet badge today, and am pleased with the result. It wasn't straight forward though, as most things Morgan aren't. The curve of the badge was greater than the original/bonnet. That was cured by placing the retaining screws between the gap between my decking planks and pressing it as flat as I could get it. Leaving a slight spring, which went when the nuts were tightened. The bolts could have been a little longer, to make putting the nuts on a bit easier, but the result below looks much better. ![[Linked Image]](https://www.tm-img.com/images/2023/06/01/PXL_20230601_144547167.jpeg) Did mine today. I have been searching for a pre-2009 cowl badge for the past 2 years. This one is the opposite to Leroy's, i.e. mine was supplied flat and I had to bend it carefully to match the cowl curvature. The fixing bolts were the right length. (Had to go for an evening drive through the New Forest, to test it). ![[Linked Image]](https://www.tm-img.com/images/2023/06/14/Cowl-badge-14-6-23.jpeg) ![[Linked Image]](https://www.tm-img.com/images/2023/06/14/Beaulieu-14-6-23.jpeg)
Peter
2009 3-litre Roadster "Ivor", royal ivory / green
|
|
|
|
|
Joined: Feb 2016
Posts: 7,919 Likes: 216
Talk Morgan Guru
|
|
Talk Morgan Guru
Joined: Feb 2016
Posts: 7,919 Likes: 216 |
Car up on ramp for another greasing session. Front suspension all tickety boo although kingpin/bush wear noticeable both sides before greasing. Confirmed that top caliper bolt can be undone with ¾"AF socket despite close proximity to main spring.
When kingpin/bush renewal takes place this winter it's nice to know I will be able to at least loosen calipers in situ, as there would be no purchase when stripped down.
Richard
2018 Roadster 3.7
1966 Land Rover S2a 88
2024 Royal Enfield Guerrilla 450
1945 Guzzi Airone
|
|
|
|
|
Joined: Dec 2020
Posts: 250 Likes: 31
Learner Plates Off!
|
|
Learner Plates Off!
Joined: Dec 2020
Posts: 250 Likes: 31 |
Set up the Bimini for tomorrow's Don Quixote rally. ![[Linked Image]](https://www.tm-img.com/images/2023/06/16/DSCN5830.jpeg) As they give even warmer weather. ![[Linked Image]](https://www.tm-img.com/images/2023/06/16/DSCN5831.jpeg)
Paul
1990 4/4 1.6 Ford CVH Sold
2014 +4 2.0 Ford
2005 BMW Z4 2.2 6Cyl Sold
|
|
|
|
|
Joined: Nov 2015
Posts: 7,893 Likes: 241
Just barreling along Talk Morgan Guru
|
|
Just barreling along Talk Morgan Guru
Joined: Nov 2015
Posts: 7,893 Likes: 241 |
Set up the Bimini for tomorrow's Don Quixote rally. Could have done with one of those for touring Welsh Wales this week...scorchio ! 
Jon M
|
|
|
|
|
Joined: Sep 2008
Posts: 952 Likes: 89
formerly known as Hugh Jorgan Talk Morgan Regular
|
|
formerly known as Hugh Jorgan Talk Morgan Regular
Joined: Sep 2008
Posts: 952 Likes: 89 |
Coincidentally I googled 'Morgan with a bimini' this afternoon....!
I was going to ask on here if anyone had got one, made one or had one made.
I know a trimmer locally so I might give them a go.
|
|
|
|
|
Joined: Aug 2020
Posts: 502
Talk Morgan Regular
|
|
Talk Morgan Regular
Joined: Aug 2020
Posts: 502 |
Replaced my bonnet badge today, and am pleased with the result. It wasn't straight forward though, as most things Morgan aren't. The curve of the badge was greater than the original/bonnet. That was cured by placing the retaining screws between the gap between my decking planks and pressing it as flat as I could get it. Leaving a slight spring, which went when the nuts were tightened. The bolts could have been a little longer, to make putting the nuts on a bit easier, but the result below looks much better. Did mine today. I have been searching for a pre-2009 cowl badge for the past 2 years. This one is the opposite to Leroy's, i.e. mine was supplied flat and I had to bend it carefully to match the cowl curvature. The fixing bolts were the right length. (Had to go for an evening drive through the New Forest, to test it). Looking good!
2004 Series 1 Roadster
|
|
|
|
|
Joined: Jul 2022
Posts: 412 Likes: 47
Learner Plates Off!
|
|
OP
Learner Plates Off!
Joined: Jul 2022
Posts: 412 Likes: 47 |
Tidied up the door sill upholstery, tacked it in place, finished the installation of the new Intatrim seats, and took it out for a quick spin. All is good with the world...
|
|
|
|
|
