|
1 members (John V6),
299
guests, and
28
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
Forums34
Topics48,335
Posts812,898
Members9,203
| |
Most Online1,046
Aug 24th, 2023
|
|
|
|
Joined: Nov 2018
Posts: 1,024 Likes: 15
Has a lot to Say!
|
OP
Has a lot to Say!
Joined: Nov 2018
Posts: 1,024 Likes: 15 |
The germans... A little bit silly ;-) In cause of their good looking I change some tools of my Morgan. So I buy a brass spanner for the centernuts of the wheels. I my eyes it wasn't only good looking, may be it's better to beat with a brass spanner on the chrome than the factory tool. This one is my toolbox: http://shop.mwsint.com/product_details.asp?id=179And I also change the hammer to this one: https://www.thorhammer.com/hammers/classic/03-212bh.htmlBut now I want to undo the wheels and don't know how to use it. The manual how to turn the nut is practical engraved on the nut, but now must the copperside hit the brass spanner oder the leatherside? Is there a difference when I close the nut? René
2018 plus4 (sports green)
with a homemade really shiny red tinted dash…
|
|
|
|
|
Joined: Jun 2015
Posts: 1,951 Likes: 40
Talk Morgan Enthusiast
|
|
Talk Morgan Enthusiast
Joined: Jun 2015
Posts: 1,951 Likes: 40 |
If using a spanner on a hexagonal wheel nut, use the copper end. If working directly on 2 or 3 eared spinners, use the hide end, to avoid damage to the spinner.
Doug
2011 Plus 4 in Rich Maroon
1972 750 “ComDom” sprinter
1958 Triton 650
1992 Triumph Trophy 900
|
|
|
|
|
Joined: Jun 2019
Posts: 1,211 Likes: 21
Has a lot to Say!
|
|
Has a lot to Say!
Joined: Jun 2019
Posts: 1,211 Likes: 21 |
If I'm reading correctly the question is which face of the hammer to use.
I would use the copper face for removal and the hide side for fitting.
This because the spinners will tighten themselves (as long as they are fitted to the correct side of the car as marked)
I'm guessing because I've never used one, I use a wooden saver. Someone with more experience will give you a definite answer.
Gordon Duguid
2014 Duratec engine plus 4, Montreal blue.
|
|
|
|
|
Joined: Dec 2008
Posts: 21,865 Likes: 167
Roadster Guru Member of the Inner Circle
|
|
Roadster Guru Member of the Inner Circle
Joined: Dec 2008
Posts: 21,865 Likes: 167 |
I always use a thick leather pad even using a copper/hide hammer on eared spinners
DaveW
'05 Red Roadster S1
'16 Yellow (Not the only) Narrow AR GDI Plus 4
|
|
|
|
|
Joined: Jun 2014
Posts: 11,610 Likes: 43
Wave & smile... It's a Morgan Member of the Inner Circle
|
|
Wave & smile... It's a Morgan Member of the Inner Circle
Joined: Jun 2014
Posts: 11,610 Likes: 43 |
If using a spanner on a hexagonal wheel nut, use the copper end. If working directly on 2 or 3 eared spinners, use the hide end, to avoid damage to the spinner. Agree I once used the copper side directly on a spinner on my first Mog and regretted it as it put a dent in the spinner. It didn’t look terrible but I knew it was there There are some rubber hammers available that have weights inside the head which give some extra power. A few Mog owners swear by them. Budster recons these are quite a bit better than the traditional copper/leather hammer
2008 XXVII Platform, Bugatti Blue Roadster 4 Seater
|
|
|
|
|
Joined: May 2011
Posts: 1,238 Likes: 2
Has a lot to Say!
|
|
Has a lot to Say!
Joined: May 2011
Posts: 1,238 Likes: 2 |
I really don't worry too much about denting the spinner. I take it as evidence that some maintenance has been carried out!
|
|
|
|
|
Joined: Apr 2008
Posts: 11,854 Likes: 137
Scruffy Oik Member of the Inner Circle
|
|
Scruffy Oik Member of the Inner Circle
Joined: Apr 2008
Posts: 11,854 Likes: 137 |
I really don't worry too much about denting the spinner. I take it as evidence that some maintenance has been carried out! 
Tim H.
1986 4/4 VVTi Sport, 2002 LR Defender, 2022 Mini Cooper SE
|
|
|
|
|
Joined: Feb 2016
Posts: 7,916 Likes: 216
Talk Morgan Guru
|
|
Talk Morgan Guru
Joined: Feb 2016
Posts: 7,916 Likes: 216 |
I quickly came to the conclusion given need to remove wheels regularly for cleaning, that a tool with adequate leverage provided least damage and best accuracy in removing/tightening spinners. There are solutions for both hex and eared spinners. I use a modified MG tool which fits nicely in my tool tray.
Richard
2018 Roadster 3.7
1966 Land Rover S2a 88
2024 Royal Enfield Guerrilla 450
1945 Guzzi Airone
|
|
|
|
|
Joined: Aug 2013
Posts: 3,383 Likes: 12
Talk Morgan Addict
|
|
Talk Morgan Addict
Joined: Aug 2013
Posts: 3,383 Likes: 12 |
At home and on ’customer’ cars I use a large and heavy Thor double white nylon, it chews the end caps but they are cheap and easy to change (still last 5 years at least) in UK like this https://leachs.net/thor-nylon-hamme...BiMHNAikgNK3qHK78-0mLzqhUQBoCVLsQAvD_BwEOut and about if needed I would use the hide side first and if it moved fine if not turn the hammer over. Remember to tighten only needs a medium weight tap as they self tighten, tap up to centralise wheel off ground, lower and a couple of Donks (technical term ;-)) to nip up and a hard brake first stop. Job done. BR Colin
BR Colin
Who used to be a Spanner Juggler
|
|
|
|
|
Joined: Nov 2013
Posts: 526 Likes: 2
Talk Morgan Regular
|
|
Talk Morgan Regular
Joined: Nov 2013
Posts: 526 Likes: 2 |
[quote=xc68anc] So I buy a brass spanner for the centernuts of the wheels. I my eyes it wasn't only good looking, may be it's better to beat with a brass spanner on the chrome than the factory tool. This one is my toolbox: http://shop.mwsint.com/product_details.asp?id=179/quote] Agree about the spanner, grips wheel nut well and does not allow you to easily overtighten.
|
|
|
|
|
