|
2 members (gomog, Taffmog),
296
guests, and
41
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
Forums34
Topics48,362
Posts813,300
Members9,215
| |
Most Online1,046
Aug 24th, 2023
|
|
|
There are no members with birthdays on this day. |
|
|
|
Joined: Aug 2020
Posts: 42
Just Getting Started
|
OP
Just Getting Started
Joined: Aug 2020
Posts: 42 |
Hi all,
I'm sure this has been asked 100 times, but I would like to put my 1997 Plus 8 up on stands and grease every point that requires it.
Could someone point me in the right direction to read a comprehensive set of instructions please?
Many thanks
Phil
|
|
|
|
|
Joined: Jul 2007
Posts: 26,756 Likes: 422
Member of the Inner Circle
|
|
Member of the Inner Circle
Joined: Jul 2007
Posts: 26,756 Likes: 422 |
Phil gomog as website is your friend
JohnV6
2022 CX Plus Four
2025 MG ZS EV aka Trigger
|
|
|
|
|
Joined: Aug 2020
Posts: 42
Just Getting Started
|
|
OP
Just Getting Started
Joined: Aug 2020
Posts: 42 |
Thanks. I am aware of this excellent web based manual.
I can only find greasing info for the Plus 4. 1960 on.
Is it the same for a Plus 8?
|
|
|
|
|
Joined: Dec 2008
Posts: 21,871 Likes: 168
Roadster Guru Member of the Inner Circle
|
|
Roadster Guru Member of the Inner Circle
Joined: Dec 2008
Posts: 21,871 Likes: 168 |
The variations are on the stub axles, where there may be just one each side, or if work has been done, also one at the top. That's assuming there is no oiler fitted!
The propshaft might have two or three, one on each UJ, and one on the sliding yoke at the front, if it has this arrangement.
If you have steering damper blades, then where they locate on the chassis needs adjusting and greasing. No nipples there though.
DaveW
'05 Red Roadster S1
'16 Yellow (Not the only) Narrow AR GDI Plus 4
|
|
|
|
|
Joined: Aug 2017
Posts: 364 Likes: 6
Learner Plates Off!
|
|
Learner Plates Off!
Joined: Aug 2017
Posts: 364 Likes: 6 |
My previous car, a 1990 build, had grease nipples on each track rod end.
Don't forget a blob of (rubber) grease under each rear wheel brake cylinder rubber boot
Also grease bonnet catch mechanisms, wheel bearings.
Sorry, other than my own personal list I don't know of other references.
Regards
Geof
70th Anniversary 4/4 (Duratec 1.8), model 1995
|
|
|
|
|
Joined: Dec 2017
Posts: 2,041 Likes: 71
Talk Morgan Expert
|
|
Talk Morgan Expert
Joined: Dec 2017
Posts: 2,041 Likes: 71 |
Thanks. I am aware of this excellent web based manual.
I can only find greasing info for the Plus 4. 1960 on.
Is it the same for a Plus 8? The answer is pretty much yes, then go to the relevant sections i.e. front suspension, there you will find particular greasing instructions. The Gearbox/Clutch and Axle section has greasing instructions long with the Rear Suspension section, etc.
Last edited by britmog; 23/06/21 03:12 PM.
Bruce
1964 4/4 Series V Comp (Megan)
1994 +8 (Maurice)
2013 M3W (Olga)
|
|
|
|
|
Joined: Jul 2007
Posts: 26,756 Likes: 422
Member of the Inner Circle
|
|
Member of the Inner Circle
Joined: Jul 2007
Posts: 26,756 Likes: 422 |
Here you go Front endAs Dave says then there is the UJ on the propshaft
JohnV6
2022 CX Plus Four
2025 MG ZS EV aka Trigger
|
|
|
|
|
