|
2 members (IcePack, +8Rich),
220
guests, and
50
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
|
|
|
Wales
by Joske Vermeule, September 1
|
|
|
|
|
|
|
Forums39
Topics49,896
Posts837,942
Members9,597
| |
Most Online1,063
Jun 14th, 2026
|
|
|
|
Joined: May 2014
Posts: 5,442 Likes: 133
Black Rat Charter Member
|
OP
Black Rat Charter Member
Joined: May 2014
Posts: 5,442 Likes: 133 |
I have just purchased one of Lionels 2 eared spinner spanners cracking piece of kit, what length breaker bar do you recommend.
Keith
2013 narrow bodied + 4 Ruby.
|
|
|
|
|
Joined: Jul 2007
Posts: 27,830 Likes: 757
Member of the Inner Circle
|
|
Member of the Inner Circle
Joined: Jul 2007
Posts: 27,830 Likes: 757 |
I have 3/4m but that is slightly too short. 1 to 1/2m might be better. I use also a mulfab spanner bolted to an old roof rack bar & that is over 2m. My front passenger side nut needs the longer bar.
But my wheels are painted & the paint I am told adds to the stiction.
JohnV6
2022 CX Plus Four
2025 Renault Scenic Alpine etech "Yvette"
|
|
|
|
|
Joined: May 2021
Posts: 58
Just Getting Started
|
|
Just Getting Started
Joined: May 2021
Posts: 58 |
I bought a Sealey 600mm 1/2 share drive which works fine for me.
I almost forgot to mention that it fits under the drivers seat as it is not too long.
Last edited by asmair; 06/08/21 04:51 PM.
|
|
|
|
|
Joined: Jul 2007
Posts: 27,830 Likes: 757
Member of the Inner Circle
|
|
Member of the Inner Circle
Joined: Jul 2007
Posts: 27,830 Likes: 757 |
Oddly it is only the RHS passenger that needs the bigger bar. Hawki's car is the same. I had thought it was just the first time I tried to remove the wheel but when I checked when Lionel's socket arrived it was the same.
JohnV6
2022 CX Plus Four
2025 Renault Scenic Alpine etech "Yvette"
|
|
|
|
|
Joined: Feb 2016
Posts: 8,694 Likes: 414
Needs to Get Out More!
|
|
Needs to Get Out More!
Joined: Feb 2016
Posts: 8,694 Likes: 414 |
I'd be a bit concerned about using too longer breaker bar as it could allow excessive torque. Although I use an MG style pressed steel tool of similar length my 600mm breaker bar would work fine allowing a couple of good nudges to ensure adequate spinner tightness.
Richard
2018 Roadster 3.7
1966 Land Rover S2a 88
2024 Royal Enfield Guerrilla 450
1945 Guzzi Airone
|
|
|
|
|
Joined: Dec 2009
Posts: 37,465 Likes: 988
Tricky Dicky Member of the Inner Circle
|
Tricky Dicky Member of the Inner Circle
Joined: Dec 2009
Posts: 37,465 Likes: 988 |
I'd be a bit concerned about using too longer breaker bar as it could allow excessive torque. Although I use an MG style pressed steel tool of similar length my 600mm breaker bar would work fine allowing a couple of good nudges to ensure adequate spinner tightness. It's the releasing not the tightening that the bar is needed for and to which John's comments applied I think.. I tighten my centrelocks with a 2' bar and release with an 8' bar attached.
2009 4/4 Sport Henrietta
1999 Indigo Blue +8
2009 4/4 Sport Green prev
1993 Con Green +8 prev
|
|
|
|
|
Joined: Jul 2007
Posts: 27,830 Likes: 757
Member of the Inner Circle
|
|
Member of the Inner Circle
Joined: Jul 2007
Posts: 27,830 Likes: 757 |
Correct taking them off. Doing up i use the mulfab tool on its own and hand tight based on it what 18 inch length
JohnV6
2022 CX Plus Four
2025 Renault Scenic Alpine etech "Yvette"
|
|
|
|
|
