|
|
|
1 members (Stevecarr),
326
guests, and
48
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
|
|
|
|
|
|
|
|
|
|
|
tow bar
by G Walker - 24/08/26 06:52 PM
|
|
|
Forums39
Topics49,836
Posts837,276
Members9,596
| |
Most Online1,063
Jun 14th, 2026
|
|
|
|
Joined: May 2022
Posts: 101 Likes: 5
L - Learner Plates On
|
OP
L - Learner Plates On
Joined: May 2022
Posts: 101 Likes: 5 |
Hi All,
Anyone know what the 'real' torque setting is for the single wheel retaining nut is for spoked wheels?
The handbook is somewhat vague with the instruction 'hammer tight'! How very 'Morgan'!
Andy
2022 Plus Four / San Marino Blue
|
|
|
|
|
Joined: Aug 2014
Posts: 2,116 Likes: 68
Talk Morgan Expert
|
|
Talk Morgan Expert
Joined: Aug 2014
Posts: 2,116 Likes: 68 |
Hello Andy perhaps this link helps. This factory makes som of the Morgan whire wheels. Torque for wire wheelsRegards von Germany Bernt
2005 4/4 1800ccm Duratec and a lot of HONDA CX500.......
|
|
|
|
|
Joined: May 2022
Posts: 101 Likes: 5
L - Learner Plates On
|
|
OP
L - Learner Plates On
Joined: May 2022
Posts: 101 Likes: 5 |
Hi Bernt,
Thank you for that. 102Nm sounds about right. I was going to call the technical people at customer services at the factory but knew common sense would prevail on this forum!
Kind regards,
Andy
Last edited by AndyMog57; 28/10/22 10:36 AM.
Andy
2022 Plus Four / San Marino Blue
|
|
|
|
|
Joined: Jan 2021
Posts: 150
L - Learner Plates On
|
|
L - Learner Plates On
Joined: Jan 2021
Posts: 150 |
That link is for conventional wheel bolts
|
|
|
|
|
Joined: Jul 2007
Posts: 27,802 Likes: 749
Member of the Inner Circle
|
|
Member of the Inner Circle
Joined: Jul 2007
Posts: 27,802 Likes: 749 |
For my S1 Roadster it was 80Nm. I checked with MMC . This is for alloys not for wire wheels.
JohnV6
2022 CX Plus Four
2025 Renault Scenic Alpine etech "Yvette"
|
|
|
|
|
Joined: Jan 2021
Posts: 150
L - Learner Plates On
|
|
L - Learner Plates On
Joined: Jan 2021
Posts: 150 |
I have assumed that the original poster is talking about knock on centrelock wire wheels? If so 80Nm would probably result in them falling off
|
|
|
|
|
Joined: Aug 2014
Posts: 2,116 Likes: 68
Talk Morgan Expert
|
|
Talk Morgan Expert
Joined: Aug 2014
Posts: 2,116 Likes: 68 |
Sorry! Here the link for Knock-on centre caps - not the torque Info you want  Fitting wire wheels
Last edited by bmgermany; 28/10/22 06:14 PM.
2005 4/4 1800ccm Duratec and a lot of HONDA CX500.......
|
|
|
|
|
Joined: Jul 2007
Posts: 27,802 Likes: 749
Member of the Inner Circle
|
|
Member of the Inner Circle
Joined: Jul 2007
Posts: 27,802 Likes: 749 |
Oh sorry. I don't think folk used torque spanners on wires. Please ignore the 80Nm.
For wires they need to be tight.
JohnV6
2022 CX Plus Four
2025 Renault Scenic Alpine etech "Yvette"
|
|
|
|
|
Joined: Jun 2022
Posts: 49 Likes: 12
Just Getting Started
|
|
Just Getting Started
Joined: Jun 2022
Posts: 49 Likes: 12 |
This is new to me too, my car is getting wire wheels too... Wire wheels this link works Go down to the bottom of the page, it says "don't overtighten them" and "As long as the hubs are fitted correctly then the spinners will self-tighten and lock as the car is driving"
Morgan Plus Four
Metallic Emerald Green and Pebble Biscuit, 'clutchless'
One of the last MY22
|
|
|
|
|
Joined: Aug 2010
Posts: 5,464 Likes: 171
Charter Member
|
|
Charter Member
Joined: Aug 2010
Posts: 5,464 Likes: 171 |
The page linked to has the following line:
There are no recommended torque settings for spinners and the exact number of turns will vary from one vehicle to the next.
I have always relied on a couple of knocks with the supplied hammer or a light tweak with the breaker bar I use for removal. They do self tighten in use - to the extent that mine can be tricky to remove as my painted wire wheels “grab” the nuts. As the text on the MWS site says:
It is very important not to over-tighten as the threads are easily damaged.
Last edited by Paul F; 28/10/22 07:58 PM.
Paul
Costock, UK
Plus Four 75th - Furka Rouge - Pip
Disco 5
Teddy - 17h1 Irish Draught cross
|
|
|
|
|
|
|
