|
10 members (Willowgreen320, stefan s, Nick55, deano, Dek, Gramrugby, ajsms999, 2949olivier, MJF, BLUE+4),
253
guests, and
121
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
Wales
by Joske Vermeule, September 1
|
|
|
|
|
|
|
|
|
|
|
Forums39
Topics49,871
Posts837,677
Members9,596
| |
Most Online1,063
Jun 14th, 2026
|
|
|
|
Joined: Jan 2016
Posts: 121
L - Learner Plates On
|
OP
L - Learner Plates On
Joined: Jan 2016
Posts: 121 |
Hi, I have a 1965 Morgan plus4 I'm having a very hard time removing the rubber fill hose for the fuel tank any suggestions thanks
|
|
|
|
|
Joined: Jan 2012
Posts: 14,976 Likes: 2
Member of the Inner Circle
|
|
Member of the Inner Circle
Joined: Jan 2012
Posts: 14,976 Likes: 2 |
Are you replacing or just removing?
If replacing I'd slit it with a blade.
Last edited by Richard - Aus; 07/04/16 10:46 AM.
Richard
1976 4/4 4 Seater
|
|
|
|
|
Joined: Mar 2012
Posts: 39
Just Getting Started
|
|
Just Getting Started
Joined: Mar 2012
Posts: 39 |
The hose can get almost welded to the tank/filler pipes after a long time. If you can get the collet on the back of the fuel filler undone a little, this will allow you to turn the filler cap in the back panel and may help release the hose. Otherwise it will probably have to be cut in the middle and prised of each end. Once you have the clips off a little WD40 in the junction behind the filler cap may help also.
This is for the flip up type filler on a two seater. Hope it helps!
|
|
|
|
|
Joined: Dec 2013
Posts: 1,075 Likes: 1
Has a lot to Say!
|
|
Has a lot to Say!
Joined: Dec 2013
Posts: 1,075 Likes: 1 |
John
Silver 2005 S1 Roadster V6 - Henrietta
|
|
|
|
|
Joined: Apr 2011
Posts: 8,015 Likes: 1
Posting Desperado Talk Morgan Guru
|
|
Posting Desperado Talk Morgan Guru
Joined: Apr 2011
Posts: 8,015 Likes: 1 |
When you replace it the new one has to be lined with a certain kind of rubber that is not by the new petrol. Replaced mine 2 year ago.
|
|
|
|
|
Joined: Dec 2011
Posts: 1,943
Talk Morgan Enthusiast
|
|
Talk Morgan Enthusiast
Joined: Dec 2011
Posts: 1,943 |
This is new to Me. I have had problems with gas hose. Cost Me an extra day in New Orleans to get it sorted. Ethanol! I now change all the gas hose every two years.
Yes I would slit the old hose to remove it.
Button
Seattle
Button
|
|
|
|
|
Joined: Jan 2016
Posts: 121
L - Learner Plates On
|
|
OP
L - Learner Plates On
Joined: Jan 2016
Posts: 121 |
can these be purchased at any auto parts store then cut to size
|
|
|
|
|
Joined: Mar 2012
Posts: 39
Just Getting Started
|
|
Just Getting Started
Joined: Mar 2012
Posts: 39 |
If IRRC for a 65 +4 they are 2 inch internal but it's not straight as you can do doubt tell from the old one. There is about a thirty degree bend about two thirds of the way down. Tall order for a local parts store I would think especially in the correct material.
|
|
|
|
|
Joined: Jan 2016
Posts: 121
L - Learner Plates On
|
|
OP
L - Learner Plates On
Joined: Jan 2016
Posts: 121 |
I spoke with Morgan spares they say the new hose is 1/8 in smaller and difficult to get on, I'm wondering if they make it in flex hose stainless
|
|
|
|
|
