|
Forums34
Topics48,364
Posts813,335
Members9,215
| |
Most Online1,046
Aug 24th, 2023
|
|
|
There are no members with birthdays on this day. |
|
|
|
Joined: Sep 2017
Posts: 72
Just Getting Started
|
OP
Just Getting Started
Joined: Sep 2017
Posts: 72 |
I buy have just discovered that my handbrake has been binding on the offside so much so that I will need to replace the shoes. I have slackened off the adjuster in the rear as much as I can but there is still some resistance in the drum, however this will of course effect the other drum as the adjuster effects both sides. I didn't notice any binding the last time I removed the rear wheels but that would have been back in September.
Any advice most welcome
Chris
2006 4/4
2006 4/4 70th Anniversary Edition
2004 3.2 Audi TT Quattro
|
|
|
|
|
Joined: Apr 2017
Posts: 1,799 Likes: 3
Talk Morgan Enthusiast
|
|
Talk Morgan Enthusiast
Joined: Apr 2017
Posts: 1,799 Likes: 3 |
Are you sure it's a handbrake problem and not a sticky slave cylinder?
Bob
2009 Black Roadster
1999 4/4 2 litre Zetec
|
|
|
|
|
Joined: Jun 2015
Posts: 1,961 Likes: 43
Talk Morgan Enthusiast
|
|
Talk Morgan Enthusiast
Joined: Jun 2015
Posts: 1,961 Likes: 43 |
Are you sure it's a handbrake problem and not a sticky slave cylinder? +1 Most likely.
Doug
2011 Plus 4 in Rich Maroon
1972 750 “ComDom” sprinter
1958 Triton 650
1992 Triumph Trophy 900
|
|
|
|
|
Joined: Dec 2009
Posts: 35,790 Likes: 471
Tricky Dicky Member of the Inner Circle
|
|
Tricky Dicky Member of the Inner Circle
Joined: Dec 2009
Posts: 35,790 Likes: 471 |
The above suggestions sound far more likely than adjustment, I had the same symptoms on my Plus 8 and changed both rear wheel cylinders and shoes at the same time, end of problem combined with regular fluid changes. Good explanation on gomog.The cylinder change is easy but take a photo of the brake shoes before you strip them and they are a bit of a wrestle to get back on but a DIY job. Good luck.
2009 4/4 Henrietta
1999 Indigo Blue +8
2009 4/4 Sport Green prev
1993 Connaught Green +8 prev
|
|
|
|
|
Joined: Jul 2007
Posts: 26,759 Likes: 424
Member of the Inner Circle
|
|
Member of the Inner Circle
Joined: Jul 2007
Posts: 26,759 Likes: 424 |
JohnV6
2022 CX Plus Four
2025 MG ZS EV aka Trigger
|
|
|
|
|
Joined: Feb 2007
Posts: 511 Likes: 1
Talk Morgan Regular
|
|
Talk Morgan Regular
Joined: Feb 2007
Posts: 511 Likes: 1 |
Slave cylinder seems to be a common fault. I’ve sorted mine several times on two different cars
Simon
2002 4/4
1936 Austin 12 light 4 Ascot saloon
2023 AMG Mercedes C300e estate
2021 Audi A1 sport
|
|
|
|
|
Joined: Dec 2009
Posts: 35,790 Likes: 471
Tricky Dicky Member of the Inner Circle
|
|
Tricky Dicky Member of the Inner Circle
Joined: Dec 2009
Posts: 35,790 Likes: 471 |
Regular fluid changes help out a bit, every two years seems to work with a bit of rubber grease behind the rear cylinder boots doesn't go amiss either.
2009 4/4 Henrietta
1999 Indigo Blue +8
2009 4/4 Sport Green prev
1993 Connaught Green +8 prev
|
|
|
|
|
Joined: Jul 2007
Posts: 28,428 Likes: 180
Salty Sea Dog Member of the Inner Circle
|
|
Salty Sea Dog Member of the Inner Circle
Joined: Jul 2007
Posts: 28,428 Likes: 180 |
When changing slave cylinders, keep the old ones and send them off to have them bored out and a stainless internal sleeve fitted.
Graham (G4FUJ)
Sold L44FOR 4/4 Giallo Fly
'09 Gen2 MINI Cooper ragtop
'90 LR 90 SW
|
|
|
|
|
Joined: Sep 2014
Posts: 989
Talk Morgan Regular
|
|
Talk Morgan Regular
Joined: Sep 2014
Posts: 989 |
Great idea Graham - the sleeved cylinders are better than new as they shouldn't go rusty. Is it "pastparts" that offer this service? Can't remember - had a few old Allegro clutch slave cylinders done some years ago.
2015 Morgan 4/4 (Wolf fettled) previously 2014 M3W
MINI Cooper S and numerous BMC/BL relics.
|
|
|
|
|
Joined: Nov 2015
Posts: 7,910 Likes: 242
Just barreling along Talk Morgan Guru
|
|
Just barreling along Talk Morgan Guru
Joined: Nov 2015
Posts: 7,910 Likes: 242 |
I've used Past Parts, great service, did a super job on a rare servo made from unobtainium, it came back with a test cert that it now held good at 46 Bar, that's over 600 psi, well pleased 
Jon M
|
|
|
|
|
