Click here to return to the home page.
Image of a road.
Who's Online Now
2 members (TalkMorgan, Saxonian), 57 guests, and 77 robots.
Key: Admin, Global Mod, Mod
Top Posters(30 Days)
+8Rich 85
Newest Members
Scot_SJI, Jimmers, Breen60, Davidmog, Stevecarr
9,596 Registered Users
Newest Topics
Wheel balance in South Devon
by AndyGoff - 29/08/26 06:24 PM
JayEmm Supersport test vid.
by Luddite - 29/08/26 11:32 AM
Grille Question
by SteveT - 29/08/26 10:51 AM
Back to Morgan!
by SteveT - 28/08/26 07:12 PM
One for howard
by +8Rich - 28/08/26 10:05 AM
Renewing the twin aero horns
by Moggo - 27/08/26 05:24 PM
4-4 zetec Fuel filter
by Phil63 - 27/08/26 03:38 PM
Latest Photos
tow bar
tow bar
by G Walker, August 24
Prescott double anniversary
Prescott double anniversary
by CooperMan, August 18
Air Crash Sites: Cairngorms
Air Crash Sites: Cairngorms
by RedThree, August 13
Four-seater luggage rack
Four-seater luggage rack
by Soleng, August 9
New M3W orange 2012
New M3W orange 2012
by jejemek, August 7
Forum Statistics
Forums39
Topics49,847
Posts837,391
Members9,596
Most Online1,063
Jun 14th, 2026
Today's Birthdays
DazMog, The Impaler, tlchzj79
Previous Thread
Next Thread
Print Thread
Joined: Aug 2011
Posts: 10
M
Menm Offline OP
New to Talk Morgan
OP Offline
New to Talk Morgan
M
Joined: Aug 2011
Posts: 10
Dear friends

When i press clutch i first have to pump it up to be able to shift gears, when i drive slowly less problems. I fill up the cylinder to control pressue.

Car was not driven regularly

What does this mean?

Thank you menm

Joined: Jul 2007
Posts: 28,894
Likes: 351
Salty Sea Dog
Member of the Inner Circle
Offline
Salty Sea Dog
Member of the Inner Circle
Joined: Jul 2007
Posts: 28,894
Likes: 351
Firstly, bleed the hydraulics to remove any air, and renew all the hydraulic fluid, to remove any possible water.

If you still have problems then there is a possibility of seal failing in either master or slave cylinder.

Regards,


Graham (G4FUJ)

Sold L44FOR 4/4 Giallo Fly
'11 MINI Countryman Cooper D All4
'90 LR 90 SW
Joined: Oct 2008
Posts: 2,125
Likes: 37
Talk Morgan Expert
Offline
Talk Morgan Expert
Joined: Oct 2008
Posts: 2,125
Likes: 37
If you need to fill the (master?) cylinder then it sounds like you have a leak. Check all four corners and the master cylinder. If one is leaking then probably best to change all the seals as the others are likely to go as well.


Regards
Alan
AP08 MOG
2016 Plus 4 GDi - Mazda Soul Red Metallic
Joined: Aug 2011
Posts: 10
M
Menm Offline OP
New to Talk Morgan
OP Offline
New to Talk Morgan
M
Joined: Aug 2011
Posts: 10

Thank you both for your answers, will check.

Thanks again!

MENM

Joined: Oct 2010
Posts: 168
F
L - Learner Plates On
Offline
L - Learner Plates On
F
Joined: Oct 2010
Posts: 168
Menm,

I had exactly the same problem with my 1993 +8. In my case it was due to the seal in the slave cylinder wearing out. It is very difficult to access the cylinder to bleed it, so although the brake fluid had been changed regularly, I don't think the clutch fluid ever had. Thus over the years dirt (corrosion?) accumulated in the cylinder and had never been flushed out, and eventually wore the seal out.

Changing it is a nasty job. I decided it would be easiest to do it by taking the gearbox cover off, but to do that you need to take the propshaft tunnel off first. So the seats and carpets had to come out too.

You might be able to get at the cylinder from the engine compartment, but I thought you would need X-ray eyes and quadruple-jointed hands and fingers so I didn't even try.

I refurbished mine - and the master cylinder while I was at it - with kits from Rutters.

What I didn't do but with hindsight perhaps should have done, is either to pipe up the bleed nipple to somewhere accessible, and/or to modify the gearbox cover to make access easier.

Hope this doesn't put you off!

Fjemog


Fjemog

1993 Plus 8
Joined: Aug 2011
Posts: 10
M
Menm Offline OP
New to Talk Morgan
OP Offline
New to Talk Morgan
M
Joined: Aug 2011
Posts: 10
Thanks for your answer and suggestions seems I need some profi help here, saves me to go crazy..... Menm


Moderated by  TalkMorgan 

Link Copied to Clipboard
Powered by UBB.threads™ PHP Forum Software 7.7.5