|
|
|
|
|
|
|
|
|
|
|
|
|
|
tow bar
by G Walker - 24/08/26 06:52 PM
|
|
|
Forums39
Topics49,836
Posts837,266
Members9,596
| |
Most Online1,063
Jun 14th, 2026
|
|
|
|
Joined: Aug 2021
Posts: 564 Likes: 79
Talk Morgan Regular
|
OP
Talk Morgan Regular
Joined: Aug 2021
Posts: 564 Likes: 79 |
We experienced almost 40 deg in shade while in France and our soft top front windscreen inner rubber seal semi bonded to the windscreens metal frame. Since then the rubber has been sticking a little when the tops up. Just wondered if anyone uses vaseline or similar on the rubber seal to enable it to fit without sticking.
dave
Dave
Plus Six "Squeak"
Roadster departed.
1936 BSA Empire Star Q8. 1935 BSA W7-35. 1938 BSA M20
|
|
|
|
|
Joined: Dec 2008
Posts: 22,356 Likes: 353
Roadster Guru Member of the Inner Circle
|
|
Roadster Guru Member of the Inner Circle
Joined: Dec 2008
Posts: 22,356 Likes: 353 |
Vaseline will do the job Dave. Watch out that the seal lips don't get doubled over at the edges.
DaveW
'05 Red Roadster S1
'16 Yellow (Not the only) Narrow AR GDI Plus 4
|
|
|
|
|
Joined: Jun 2015
Posts: 2,084 Likes: 69
Talk Morgan Expert
|
|
Talk Morgan Expert
Joined: Jun 2015
Posts: 2,084 Likes: 69 |
A smear of silicon grease may be even better as it has a much higher melting point.
Doug
2011 Plus 4 in Rich Maroon
1972 750 “ComDom” sprinter
1958 Triton 650
1992 Triumph Trophy 900
|
|
2 members like this:
Whizjet, RichardV6 |
|
|
|
|
Joined: Jul 2011
Posts: 1,242 Likes: 30
Has a lot to Say!
|
|
Has a lot to Say!
Joined: Jul 2011
Posts: 1,242 Likes: 30 |
I use This stuff. Got it when I had a H2000 & was recommended “part” to stop squeaks from the soft top.
4/4 Ivory 4.1:1 axle, Mercedes A200 AMG
|
|
1 member likes this:
Whizjet |
|
|
|
|
Joined: Jan 2023
Posts: 1,013 Likes: 119
Has a lot to Say!
|
|
Has a lot to Say!
Joined: Jan 2023
Posts: 1,013 Likes: 119 |
Yep silicon lubricant, looks like vaseline but doesn't melt. Apply to the inside of the channel annually with a small piece of rag that you have manipulated the grease into. LESS is more! As Dave said, always make sure the seal is not doubled back on itself when fitting and if the ends are coming unstuck re=glue them in place. I did a post some time back or PM me if you need further advice!
|
|
1 member likes this:
Whizjet |
|
|
|
|
Joined: Aug 2021
Posts: 564 Likes: 79
Talk Morgan Regular
|
|
OP
Talk Morgan Regular
Joined: Aug 2021
Posts: 564 Likes: 79 |
Thanks everyone, I have clear silicon grease in the garage, so i will use a small amount as advised.
Dave
Plus Six "Squeak"
Roadster departed.
1936 BSA Empire Star Q8. 1935 BSA W7-35. 1938 BSA M20
|
|
|
|
|
|
|
