|
1 members (Marmota),
342
guests, and
79
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
Wales
by Joske Vermeule, September 1
|
|
|
|
|
|
|
|
|
|
|
Forums39
Topics49,867
Posts837,614
Members9,596
| |
Most Online1,063 Jun 14th, 2026
|
|
|
|
Joined: Dec 2015
Posts: 938 Likes: 19
Talk Morgan Regular
|
OP
Talk Morgan Regular
Joined: Dec 2015
Posts: 938 Likes: 19 |
I have a 1994 Plus 8 with 26K mileage. An annoying intermittent squeak (more noticeable when idling) has developed which disappears when I just gently touch the clutch pedal. I have well lubricated the pedal shaft but this squeak still persists. The clutch otherwise is working fine as with the rest of the car. A new cluch cylinder was fitted by the previous owner about 12 months ago. Possibly the clutch bearing? Any suggestions other than ear plugs?
|
|
|
|
|
Joined: May 2014
Posts: 5,442 Likes: 133
Black Rat Charter Member
|
Black Rat Charter Member
Joined: May 2014
Posts: 5,442 Likes: 133 |
Sounds like the bearing to me, try winding it up to 4000 rpm and dropping the clutch, kill or cure.
Keith 2013 narrow bodied + 4 Ruby.
|
|
|
|
|
Joined: Dec 2015
Posts: 938 Likes: 19
Talk Morgan Regular
|
OP
Talk Morgan Regular
Joined: Dec 2015
Posts: 938 Likes: 19 |
Sounds like the bearing to me, try winding it up to 4000 rpm and dropping the clutch, kill or cure. I've just given that a try and the sqeak seems less audible. The clutch bite is spot on and crisp. If it is the clutch thrust bearing do you think it may eventually get better with wear or is a replacement the only option?
|
|
|
|
|
Joined: Dec 2008
Posts: 22,366 Likes: 354
Roadster Guru Member of the Inner Circle
|
Roadster Guru Member of the Inner Circle
Joined: Dec 2008
Posts: 22,366 Likes: 354 |
It could go either way in my experience. I once had to drop an Escort gearbox when the squeak became intolerable.
Two other options. Depending on the type of clutch lever, you might be able to add just enough preloaded to stop the squeak. Even lubricating the pivot might be enough.
If you can see inside the bell-housing you might consider a tiny squirt of lubricant but be very careful. I once lost the plastic tube off a can of something when it pinged into the bell housing.......
DaveW '05 Red Roadster S1 '16 Yellow (Not the only) Narrow AR GDI Plus 4
|
|
|
|
|
Joined: May 2014
Posts: 5,442 Likes: 133
Black Rat Charter Member
|
Black Rat Charter Member
Joined: May 2014
Posts: 5,442 Likes: 133 |
Sounds like the bearing to me, try winding it up to 4000 rpm and dropping the clutch, kill or cure. I've just given that a try and the sqeak seems less audible. The clutch bite is spot on and crisp. If it is the clutch thrust bearing do you think it may eventually get better with wear or is a replacement the only option? Try it again, it may be that soft driving has polished the bearing
Keith 2013 narrow bodied + 4 Ruby.
|
|
|
|
|
Joined: Dec 2015
Posts: 938 Likes: 19
Talk Morgan Regular
|
OP
Talk Morgan Regular
Joined: Dec 2015
Posts: 938 Likes: 19 |
Sounds like the bearing to me, try winding it up to 4000 rpm and dropping the clutch, kill or cure. I've just given that a try and the sqeak seems less audible. The clutch bite is spot on and crisp. If it is the clutch thrust bearing do you think it may eventually get better with wear or is a replacement the only option? Try it again, it may be that soft driving has polished the bearing Thanks for your advice. I'll give it a go. The car has done about a 1000 miles a year from new and cosseted throughout its life. Next time I'll take it out I'll wring its neck a bit! 😉
|
|
|
|
|
Joined: May 2014
Posts: 2,780 Likes: 5
Talk Morgan Expert
|
Talk Morgan Expert
Joined: May 2014
Posts: 2,780 Likes: 5 |
Is it a carbon or a bearing thrust? I'm not familiar with these boxes but maybe you have an access hole or rubber cover around the clutch fork? A little squirt might be enough to quieten it?
Steve
|
|
|
|
|
Joined: Aug 2015
Posts: 1,616 Likes: 143
Talk Morgan Enthusiast
|
Talk Morgan Enthusiast
Joined: Aug 2015
Posts: 1,616 Likes: 143 |
Also consider the clutch pilot bearing as well.
Arwyn
|
|
|
|
|
Joined: Dec 2015
Posts: 938 Likes: 19
Talk Morgan Regular
|
OP
Talk Morgan Regular
Joined: Dec 2015
Posts: 938 Likes: 19 |
Is it a carbon or a bearing thrust? I'm not familiar with these boxes but maybe you have an access hole or rubber cover around the clutch fork? A little squirt might be enough to quieten it? I'm not sure Steve, but will take your advice and try it. Thanks, Paul.
|
|
|
|
|
Joined: Dec 2008
Posts: 22,366 Likes: 354
Roadster Guru Member of the Inner Circle
|
Roadster Guru Member of the Inner Circle
Joined: Dec 2008
Posts: 22,366 Likes: 354 |
I doubt it will be a carbon bearing from that year.
DaveW '05 Red Roadster S1 '16 Yellow (Not the only) Narrow AR GDI Plus 4
|
|
|
|
|