|
7 members (GrandadC, AlyMatt, High Hamster, JohnHarris, MJF, Oskar, B3MOG),
302
guests, and
37
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
Forums34
Topics48,335
Posts812,889
Members9,203
| |
Most Online1,046
Aug 24th, 2023
|
|
|
|
Joined: Aug 2011
Posts: 2,583
Talk Morgan Expert
|
OP
Talk Morgan Expert
Joined: Aug 2011
Posts: 2,583 |
I took advantage of the warm weather today to grease the kingpins, only to find that the offside one was hidden behind the damper and I had to loosen it to enable the grease gun to clamp onto it. I`ve not had this problem before so I wonder if the nipple was changed at the last service for some reason. I`ll see about changing it for a differently angled one at the Resto Show.The nearside one was done in a couple of minutes. Also cleaned the inside of the wheels with WD40 whilst the wheels were off the ground.
Then I took Megan out for a blast to check everything was OK and had a great top-down run for 30+ miles around the lanes of South Derbyshire. Days like today make me realise what a great privilege it is to have the ability to climb into a Morgan on a whim and just take off into the countryside. I got behind 4 hooded youths in a Peugeot with baked bean can exhaust and at a road works traffic light they all turned round and waved at me giving the thumbs up and smiling like toddlers - There`s hope for us yet!
Last edited by PhilRoyle; 15/02/19 04:30 PM.
2010 4/4 sport - le mans green
|
|
|
|
|
Joined: Jan 2011
Posts: 5,366 Likes: 14
Charter Member
|
|
Charter Member
Joined: Jan 2011
Posts: 5,366 Likes: 14 |
I have always had this problem with the off side nipple whereas the nearside is fine. I wonder why they should be so different?
110 mile run out today in beautiful sunshine to see the progress on the SS100.
Here for a good time not a long time!!
Reg
|
|
|
|
|
Joined: Jul 2007
Posts: 26,746 Likes: 419
Member of the Inner Circle
|
|
Member of the Inner Circle
Joined: Jul 2007
Posts: 26,746 Likes: 419 |
I loosen the nipple off with a spanner to get access
JohnV6
2022 CX Plus Four
2025 MG ZS EV aka Trigger
|
|
|
|
|
Joined: Feb 2016
Posts: 7,916 Likes: 216
Talk Morgan Guru
|
|
Talk Morgan Guru
Joined: Feb 2016
Posts: 7,916 Likes: 216 |
Try a different grease gun head or adjust your existing one. I bought a cheap new one with flex hose and have had no trouble latching on since 😆
Richard
2018 Roadster 3.7
1966 Land Rover S2a 88
2024 Royal Enfield Guerrilla 450
1945 Guzzi Airone
|
|
|
|
|
Joined: Sep 2013
Posts: 1,118
Has a lot to Say!
|
|
Has a lot to Say!
Joined: Sep 2013
Posts: 1,118 |
Snap! Must be the weather for it! But my nipples behaved themselves!
RogT Old Git Racer ex 4/4 sand 2013
+4 GDI Royal Ivory 2015
Ford Fiesta ST2
|
|
|
|
|
Joined: Nov 2013
Posts: 526 Likes: 2
Talk Morgan Regular
|
|
Talk Morgan Regular
Joined: Nov 2013
Posts: 526 Likes: 2 |
You need to get the angle of the grease gun and the nipple to match so that the nipple can get into the grease gun head.
This is different on each side on my plus 4 and I have to turn the wheel a bit further out to do the offside.
|
|
|
|
|
Joined: May 2010
Posts: 9,285 Likes: 69
Needs to Get Out More!
|
|
Needs to Get Out More!
Joined: May 2010
Posts: 9,285 Likes: 69 |
My offside nipple is also blocked off by the damper so turning the wheel slightly is the way to give clearance.
Plus Four MY23 Furka Rouge
|
|
|
|
|
Joined: Nov 2016
Posts: 184 Likes: 2
L - Learner Plates On
|
|
L - Learner Plates On
Joined: Nov 2016
Posts: 184 Likes: 2 |
Also went for a spin today and come back and got the grease gun and my nipples behaved as well and then fitted Dave's mohair gaiters.
Ian
2019 +4 110 Anniversary Bentley Velvet Red.
|
|
|
|
|
Joined: Dec 2018
Posts: 308
Learner Plates Off!
|
|
Learner Plates Off!
Joined: Dec 2018
Posts: 308 |
I bought a nipple gripper 🤪. Works really well.
John
1936 Austin Seven Ulster Replica
|
|
|
|
|
Joined: Oct 2016
Posts: 509 Likes: 1
Talk Morgan Regular
|
|
Talk Morgan Regular
Joined: Oct 2016
Posts: 509 Likes: 1 |
I'm struggling with the nipples on my prop shaft... any tips on that? It seems to partially latch but when I pump the gun the nozzle just jumps off.
|
|
|
|
|
